Blumat irrigation systems operate between about 1 PSI and 15 PSI.

Blumat sensors rely on low water pressure. If pressure falls below roughly 1 PSI the sensor cannot release water. If pressure exceeds about 15 PSI fittings or tubing may leak or disconnect. Different distribution methods perform best at different pressures, but all must stay within this safe range. Step by Step Instructions:1. Identify the pressure of your water source.2. Ensure pressure is above 1 PSI so the sensors can release water.3. Keep pressure below 15 PSI.4. Install a pressure reducer when connecting to pressurized water lines.

What Pressure Does a Blumat System Need?

Every 2 feet 4 inches of water height creates about 1 PSI of pressure.

Gravity systems generate pressure based on elevation. Approximately every 2 feet 4 inches of height equals 1 PSI of pressure. Most systems require about 3 feet of height or more to operate reliably, though the exact requirement depends on the distribution method. Step by Step Instructions:1. Measure the vertical distance from the reservoir water level to the grow area.2. Use roughly 2 ft 4 in per PSI as a guideline.3. Raise the reservoir if pressure is too low.4. Confirm water flows evenly through the system.

How High Should a Gravity Reservoir Be?

Sustainable Village

Water Source & Pressure

Start Here

What is your cancellation policy?

Can I edit or add anything to my order?

How do I cancel my order?

What do I do if my item(s) arrives damaged?

My order was marked delivered but it’s not here.

What do I do if I receive the wrong item in my order?

How do I track my order?

Do you ship worldwide?

Do you offer expedited shipping?

How much does shipping cost?

What if my package gets lost or arrives damaged?

Do you offer free shipping?

Shipping, Tracking & Order Questions

Orders, Shipping & Returns

Do you offer refunds or exchanges?

When will I get my refund?

What’s your return policy?

How do I make a return?

How do I start a return?

Moisture Monitoring

What Is a Blumat Watering System?

Why Use Blumat Instead of a Timer?

System Overview

What Is the Ideal Soil Moisture Range?

How Do You Adjust a Blumat Sensor?

How Long Should You Wait After Adjusting a Sensor?

Sensors & Moisture

What Is BluSoak Drip Tape?

How Close Should the Sensor Be to the Water Source?

Distribution Methods

Why Is My Blumat System Overwatering?

Troubleshooting

How Do You Install a Blumat Sensor?

How Do You Soak Blumat Sensors Before Installation?

What Causes Soil to Become Hydrophobic?

Why Is My System Not Watering?

How Do You Remove Air From Irrigation Lines?

Why Are Some Pots Wetter Than Others?

How Do You Check If a Sensor Is Running?

How Do You Fix a Leaking Fitting?

How Should Reservoirs Be Maintained?

Can Nutrients Be Fed Through the System?

Should Biological Products Be Run Through Blumats?

How Do You Clean a Reservoir?

How Do You Prevent Algae in Irrigation Systems?

How Do You Install BluSoak in a Bed?

How Do You Lay Out BluSoak in Containers?

How Do You Repair Drip Tape?

How Do You Troubleshoot Pressure Problems?

Why Does Sensor Depth Matter?

How Do You Reset a Blumat Sensor?

How Do You Measure Soil Moisture Accurately?

How Do You Install a Blumat Sensor? Guide

How Do You Soak Blumat Sensors Before Installation? Guide

What Causes Soil to Become Hydrophobic? Guide

Why Is My System Not Watering? Guide

How Do You Remove Air From Irrigation Lines? Guide

Why Are Some Pots Wetter Than Others? Guide

How Do You Check If a Sensor Is Running? Guide

How Do You Fix a Leaking Fitting? Guide

How Should Reservoirs Be Maintained? Guide

Can Nutrients Be Fed Through the System? Guide

Should Biological Products Be Run Through Blumats? Guide

How Do You Clean a Reservoir? Guide

How Do You Prevent Algae in Irrigation Systems? Guide

How Do You Install BluSoak in a Bed? Guide

How Do You Lay Out BluSoak in Containers? Guide

How Do You Repair Drip Tape? Guide

How Do You Troubleshoot Pressure Problems? Guide

Why Does Sensor Depth Matter? Guide

How Do You Reset a Blumat Sensor? Guide

How Do You Measure Soil Moisture Accurately? Guide

General Help Center

Blumat Classic Stakes & Bottle Adapters

Watering Houseplants with Blumat

Vacation Watering: Keeping Plants Alive While You're Away

Houseplants & Vacation Watering

Gravity Fed Systems: Raised Reservoir & Off-Grid Setups

How Blumat Watering Systems Work

Setting Up Your Blumat Sensors

Blumat Distribution Methods: Drippers, Rings, BluSoak & AquaMats

Supply Lines & System Layout

Blumat Distribution Methods: Drippers, Rings, BluSoak & AquaMats copy

Gravity Fed Systems

Pressurized Systems: Backyard Gardens, Grow Tents & Indoor Grows

Commercial Cultivation: Large Scale Blumat Systems

Choosing Your Water Source & Pressure

Troubleshooting Your Blumat System

Pro Tips: Transplanting, Feeding, Harvest & More

Pressurized Systems