Many growers operate Blumat systems around 50–100 mbar of soil tension.

Soil moisture tension is measured in millibar (mbar). Lower numbers represent wetter soil while higher numbers represent drier soil. Many growing systems perform well in the 50&#x2013;100 mbar range, though the ideal level varies depending on soil type, plant stage, and environmental conditions. Step by Step Instructions:1. Measure soil moisture using a tensiometer.2. Compare the reading to the desired range.3. Adjust the sensor slightly if needed.4. Allow time for the soil to stabilize before adjusting again.

What Is the Ideal Soil Moisture Range?

Tightening the adjustment cap makes the system run drier while loosening makes it wetter.

Blumat sensors should be adjusted in very small increments. A small change in the cap position can significantly change the moisture target. After adjusting, allow the soil to stabilize before deciding whether another change is necessary. Step by Step Instructions:1. Measure current soil moisture.2. Insert the adjustment key into the sensor.3. Turn slightly tighter for drier soil or slightly looser for wetter soil.4. Wait before making another adjustment.

How Do You Adjust a Blumat Sensor?

Wait up to 24–48 hours for soil moisture to stabilize before adjusting again.

Soil moisture changes slowly, especially in larger containers and beds. Making repeated adjustments too quickly can push the system far past the desired moisture level. Waiting a full day or two helps ensure that each adjustment is based on stable soil conditions. Step by Step Instructions:1. Make a small adjustment to the sensor.2. Leave the system unchanged for at least a day.3. Measure soil moisture during this time.4. Adjust again only if the system remains outside the target range.

How Long Should You Wait After Adjusting a Sensor?

Sustainable Village

Sensors & Moisture

Start Here

What is your cancellation policy?

Can I edit or add anything to my order?

How do I cancel my order?

What do I do if my item(s) arrives damaged?

My order was marked delivered but it’s not here.

What do I do if I receive the wrong item in my order?

How do I track my order?

Do you ship worldwide?

Do you offer expedited shipping?

How much does shipping cost?

What if my package gets lost or arrives damaged?

Do you offer free shipping?

Shipping, Tracking & Order Questions

Orders, Shipping & Returns

Do you offer refunds or exchanges?

When will I get my refund?

What’s your return policy?

How do I make a return?

How do I start a return?

Moisture Monitoring

What Is a Blumat Watering System?

Why Use Blumat Instead of a Timer?

System Overview

What Pressure Does a Blumat System Need?

How High Should a Gravity Reservoir Be?

Water Source & Pressure

What Is BluSoak Drip Tape?

How Close Should the Sensor Be to the Water Source?

Distribution Methods

Why Is My Blumat System Overwatering?

Troubleshooting

How Do You Install a Blumat Sensor?

How Do You Soak Blumat Sensors Before Installation?

What Causes Soil to Become Hydrophobic?

Why Is My System Not Watering?

How Do You Remove Air From Irrigation Lines?

Why Are Some Pots Wetter Than Others?

How Do You Check If a Sensor Is Running?

How Do You Fix a Leaking Fitting?

How Should Reservoirs Be Maintained?

Can Nutrients Be Fed Through the System?

Should Biological Products Be Run Through Blumats?

How Do You Clean a Reservoir?

How Do You Prevent Algae in Irrigation Systems?

How Do You Install BluSoak in a Bed?

How Do You Lay Out BluSoak in Containers?

How Do You Repair Drip Tape?

How Do You Troubleshoot Pressure Problems?

Why Does Sensor Depth Matter?

How Do You Reset a Blumat Sensor?

How Do You Measure Soil Moisture Accurately?

How Do You Install a Blumat Sensor? Guide

How Do You Soak Blumat Sensors Before Installation? Guide

What Causes Soil to Become Hydrophobic? Guide

Why Is My System Not Watering? Guide

How Do You Remove Air From Irrigation Lines? Guide

Why Are Some Pots Wetter Than Others? Guide

How Do You Check If a Sensor Is Running? Guide

How Do You Fix a Leaking Fitting? Guide

How Should Reservoirs Be Maintained? Guide

Can Nutrients Be Fed Through the System? Guide

Should Biological Products Be Run Through Blumats? Guide

How Do You Clean a Reservoir? Guide

How Do You Prevent Algae in Irrigation Systems? Guide

How Do You Install BluSoak in a Bed? Guide

How Do You Lay Out BluSoak in Containers? Guide

How Do You Repair Drip Tape? Guide

How Do You Troubleshoot Pressure Problems? Guide

Why Does Sensor Depth Matter? Guide

How Do You Reset a Blumat Sensor? Guide

How Do You Measure Soil Moisture Accurately? Guide

General Help Center

Blumat Classic Stakes & Bottle Adapters

Watering Houseplants with Blumat

Vacation Watering: Keeping Plants Alive While You're Away

Houseplants & Vacation Watering

Gravity Fed Systems: Raised Reservoir & Off-Grid Setups

How Blumat Watering Systems Work

Setting Up Your Blumat Sensors

Blumat Distribution Methods: Drippers, Rings, BluSoak & AquaMats

Supply Lines & System Layout

Blumat Distribution Methods: Drippers, Rings, BluSoak & AquaMats copy

Gravity Fed Systems

Pressurized Systems: Backyard Gardens, Grow Tents & Indoor Grows

Commercial Cultivation: Large Scale Blumat Systems

Choosing Your Water Source & Pressure

Troubleshooting Your Blumat System

Pro Tips: Transplanting, Feeding, Harvest & More

Pressurized Systems